Flux Cored Wire(FCAW)


ProductProductAWSJISENGBApplication
SFC-71SFC-71A5.20
E71T-1C/1M
Z3313 T 49 2
T1-1 C/M A-U
ISO 17632-A
T42 2 P C/M 1 H5
T10045
E501T-1/1M
For welding shipbuilding storage vessels , structural fabrication , machinery and piping etc.
SFC-70CSFC-70CA5.20
E70T-1C
Z3313 T 49 2
T15-0 C A-U
ISO 17632-A
T42 2 M C 3 H5
T10045
E500T-1
It's a metal type flux cored wire to be used by CO2 gas shielding . The porosity resistibility to inorganic zinc primer is better.
SFC-71NiSFC-71NiA5.20
E71T-1C/M-J
Z3313 T 49 4
T1-1 C/M A-N1-U
ISO 17632-A
T42 4 P C/M 1 H5
T10045
E501T-1L/1ML
Rutile-type FCW and excellent impact value at - 40℃.
SFC-71JSFC-71JA5.20
E71T-1C/M-J
Z3313 T 49 4
T1-1 C/M A-U
ISO 17632-A
T46 4 P C/M 1 H5
T10045
E501T-1L/1ML
Rutile-type FCW and excellent impact value at - 40℃.
SFC-71MSFC-71MA5.18
E70C-6C/6M
Z3313 T 49 4
T15-0 C/M A-U
ISO 17632-A
T42 4 M C/M 3 H5
--Mixed gas Rutile-type FCW . Good weldability on all-position and excellent impact value.
SFC-75SFC-75A5.20
E71T-5C/5M
Z3313 T 49 3
T5-1 C/M A-U
ISO 17632-A
T42 3 B C/M 1 H5
T10045
E501T-5/5M
Suits for mild steel and 490N/mm2 H.T. steel , good impact value at - 30℃.
SFC-04SFC-04A5.20
E70T-4
Z3313 T 49
T4-0 N A
ISO 17632-A
T42 Z W N 3
T10045
E500T-4
Welding for civil construction , building and machinery . It also can be applied to build up for hardfacing.
SFC-07SFC-07A5.20
E70T-7
Z3313 T 49
T7-0 N A
ISO 17632-A
T42 Z W N 3
T10045
E500T-7
High deposition rate and deep penetration . Suits for mild steel and 490N/mm2 H.T. steel.
SFC-18SFC-18A5.20
E71T-8
Z3313 T 49
T7-3 N A
ISO 17632-A
T42 3 P N 1
T10045
E501T-8
All position self-shield flux cored wire used for mild steel and 490N/mm2 H.T. steel.
SFC-71GSFC-71GA5.20
E71T-G
Z3313 T 49
TG-1 N A
ISO 17632-A
T42 Z Y N 1
T10045
E501T-G
All position self-shield flux cored wire used for mild steel and 490N/mm2 H.T. steel.
AFL-X70-OAFL-X70-OA5.29
E71T8-Ni1J
--ISO 17632-A
T42 3 1Ni P N 1
T17493
E491T8-Ni1J
For welding X70 pipe steel.
SFC-101SFC-101A5.29
E101T1-GC/GM
------For 690N/mm2 H.T. steel welding.
SFC-110SFC-110A5.29
E111T1-GC/GM
------For 780N/mm2 H.T. steel welding .
SFC-120SFC-120A5.29
E121T1-GC/GM
------For 830N/mm2 H.T. steel welding .
AFR-X80-OAFR-X80-OA5.29
E81T8-Ni2J H8
--ISO 17632-A
T46 3 2Ni P N 1
T17493
E551T8-Ni2J H8
For welding X80 pipe steel.
SFC-81A1SFC-81A1A5.29
E81T1-A1C
Z3318
T55T1-1C-2M3
ISO 17634-A
T Mo P C 1 H5
T17493
E551T1-A1
For welding 0.5%Mo low alloy steels .
SFC-81B2SFC-81B2A5.29
E81T1-B2C
Z3318
T55T1-1C-1CM
ISO 17634-A
T CrMo1 P C 1 H5
T17493
E551T1-B2
For welding 1.25Cr-0.5%Mo low alloy steels in thermoelectric power plant and oil refiner.
SFC-91B3SFC-91B3A5.29
E91T1-B3C
Z3318
T62T1-1C-2C1M
ISO 17634-A
T CrMo2 P C 1 H5
T17493
E601T1-B3
For welding 2.25Cr-1%Mo low alloy steels in thermoelectric power plant and oil refiner.
SFC-81Ni1SFC-81Ni1A5.29
E81T1-Ni1C
Z3313 T 55 3
T1-1 C A-N2
ISO 17632-A
T46 3 1Ni P C 1 H5
T17493
E551T1-Ni1
For 590N/mm2 H.T. steel welding.
SFC-81Ni2SFC-81Ni2A5.29
E81T1-Ni2C
Z3313 T 55 4
T1-1 C A-N5
ISO 17632-A
T46 4 2Ni P C 1 H5
T17493
E551T1-Ni2
Good weldability on all-position and can be used to weld 2~3%Ni steel.
SFC-91Ni2SFC-91Ni2A5.29
E91T1-Ni2C
Z3313 T 62 4
T1-1 C A-N5
ISO 17632-A
T50 4 2Ni P C 1 H5
T17493
E601T1-Ni2
Good weldability on all-position and can be used to weld 2~3%Ni steel.
SFC-81K2SFC-81K2A5.29
E81T1-K2C
Z3313 T 55 6
T1-1 C A-N3
ISO 17632-A
T46 6 1.5Ni P C 1 H5
T17493
E551T1-K2
Good notch toughness can be obtained at -60℃.
SFC-81MSFC-81MA5.28
E80C-G
--ISO 17632-A
T46 6 Z M C/M 3 H5
--It is widely used for flat and horizontal fillet welding in shipbuilding, bridges, vechicle, machinery and structural fabrication etc.
SFC-81W2SFC-81W2A5.29
E81T1-W2C
Z3320
YFA-58W
--T17493
E551T1-W
For butt or fillet MAG welding of 590N/mmm2 weather-proof steel and A588 steel.
SFC-307SFC-307A5.22
E307T1-1
Z3323
TS307-FC1
ISO 17633-A
T 18 9 Mn Mo P C/M 2
--For welding higher carbon 19%Cr-9%Ni-4Mn steels.
SFC-308HSFC-308HA5.22
E308HT1-1
Z3323
TS308H-FC1
ISO 17633-A
T 19 9 P C/M 2
T17853
E308HT1-1
For welding higher carbon 18%Cr-8%Ni steels such as AISI 304, 308 .
SFC-308LSFC-308LA5.22
E308LT1-1
Z3323
TS308L-FC1
ISO 17633-A
T 19 9 L P C/M 2
T17853
E308LT1-1
For welding low carbon 18%Cr-8%Ni steels such as AISI 304, 308 .
SFC-309LSFC-309LA5.22
E309LT1-1
Z3323
TS309L-FC1
ISO 17633-A
T 23 12 L P C/M 2
T17853
E309LT1-1
For low carbon of 22%Cr-12%Ni stainless steel and welding for dissimilar steels.
SFC-309MoLSFC-309MoLA5.22
E309LMoT1-1
Z3323
TS309LMo-FC1
ISO 17633-A
T 23 12 2 L P C/M 2
T17853
E309LMoT1-1
It suits for welding of dissimilar steel.
SFC-312SFC-312A5.22
E312T1-1
Z3323
TS312-FC1
ISO 17633-A
T 29 9 P C/M 2
T17853
E312T1-1
It is suitable for welding dissimilar metals such as stainless steels and low-alloy steels, as well as for joining those steels which are hard to weld or possible to cause porosity during welding.
SFC-312MSFC-312M--------For welding of higher carbon steel and low-alloyed steel .
SFC-316LSFC-316LA5.22
E316LT1-1
Z3323
TS316L-FC1
ISO 17633-A
T 19 12 3 L P C/M 2
T17853
E316LT1-1
For welding low carbon 18%Cr-12%Ni-2.5%Mo steels with better corrosion resistance.
SFC-316HSFC-316HA5.22
E316HT1-1
Z3323
TS316H-FC1
ISO 17633-A
T 19 12 3 P C/M 2
T17853
E316HT1-1
For welding higher carbon 18%Cr-12%Ni-2.5%Mo steels with better corrosion resistance.
SFC-317LSFC-317LA5.22
E317LT1-1
Z3323
TS317L-FC1
ISO 17633-A
T 19 13 4 L P C/M 2
T17853
E317LT1-1
For welding low carbon 18%Cr-12%Ni-3.5%Mo steels with better corrosion resistance.
SFC-318SFC-318----ISO 17633-A
T 19 12 3 Nb P C/M 2
--For welding stabilised and/or unstabilised Mo-bearing austenite stainless steels.
SFC-347LSFC-347LA5.22
E347T1-1
Z3323
TS347-FC1
ISO 17633-A
T 19 9 Nb P C/M 2
T17853
E347T1-1
For welding 18%Cr-9%Ni-Nb steels or 18%Cr-9%Ni-Ti steels.
SFC-347HSFC-347HA5.22
E347HT1-1
Z3323
TS347H-FC1
ISO 17633-A
T 19 9 Nb P C/M 2
T17853
E347HT1-1
For welding 18%Cr-9%Ni-Nb steels or 18%Cr-9%Ni-Ti steels.
SFC-410SFC-410A5.22
E410T1-1
Z3323
TS410-FC1
ISO 17633-A
T 13 P C/M 2
T17853
E410T1-1
For 13%Cr stainless steel welding.
SFC-410NMSFC-410NMA5.22
E410NiMoT1-G
------It suits for metal to metal abrasion and/or within corrosion environment.
SFC-410NiMoSFC-410NiMoA5.22
E410NiMoT1-1
Z3323
TS410NiMo-FC1
ISO 17633-A
T 13 4 P C/M 2
T17853
E410NiMoT1-1
For welding of ASTM CA6NM or steels with similar chemical composition
SFC-2209SFC-2209A5.22
E2209T1-1
Z3323
TS2209-FC1
ISO 17633-A
T 22 9 3 N L P C/M 2
T17853
E2209T1-1
For welding alloy 2205 duplex stainless steel with resistance to pitting corrosion and crack.
SFC-2594SFC-2594A5.22
E2594T1-1
--ISO 17633-A
T 25 9 4 N L P C/M 2
--For welding alloy 2507 duplex stainless steel with resistance to pitting corrosion and crack.
SFC-2509SFC-2509--------For welding alloy 2505 duplex stainless steel with resistance to pitting corrosion and crack.
SFC-409TiSFC-409TiA5.22
EC409
Z3323
TS409-FCO
ISO 17633-A
T 13 Ti M M 2
--For welding AISI409 stainless steel and similar alloy steel.
SFC-409CbSFC-409CbA5.22
EC409Nb
Z3323
TS409Nb-FCO
----For welding AISI409 stainless steel and similar alloy steel.
SFC-439TiSFC-439TiA5.22
EC439
------For welding AISI439 stainless steel and similar alloy steel.
SFH-12SSFH-12S--------Excellent abrasion resistance . Flux combination SF-80.
SFH-17SSFH-17S--------Used for metal to metal abrasion , excellent impact resistance . Flux combination SF-80.
SFH-22SSFH-22S--------For build-up and/or buttering on high carbon steel with excellent resistance to crack. Flux combination SF-82.
SFH-31SSFH-31S--------It suits for build-up of continuous casting rolls, steel mill rolls, shafts, idlers, joumals or work pieces that machinability is required. Flux combination SF-80.
SFH-42SSFH-42S--------For rebuilding continuous casting rolls under high temperature service in steel mill.
SFH-53SSFH-53S--------Good heat adhesion resistance and bead marks resistance.
SFH-55SSFH-55S--------Good heat adhesion resistance and bead marks resistance.
SFH-MNGSFH-MNG--------Excellent resistance to heavy impact .It's suitable for repair of 13%Mn steels and crushing hammers.
SFH-25GSFH-25G--------For rebuild the worn part of crane wheel ,bulldozer blade, crusher jaw, shovel tooth and dipper tip .
SFH-35GSFH-35G--------For rebuilding the gears, track and chain.
SFH-42MGSFH-42MG--------It suits for the parts subjected to servere soil abrasion and corrosive wear.
SFH-45GSFH-45G--------For rebuilding the gears, track and chain.
SFH-50GSFH-50G--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-55GSFH-55G--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-58GSFH-58G--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-58GMSFH-58GM--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-59GSFH-59G--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-61GMSFH-61GM--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-61NbGMSFH-61NbGM--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-62GMSFH-62GM--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-63GSFH-63G--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-66WGSFH-66WG--------It is suitable for hardfacing of bulldozer blade, bucket lip, tipper teeth, the parts of impeller subjected to severe soil abrasion.
SFH-67NMGSFH-67NMG--------It is suitable for hardfacing of wearing liner plate, agitator propeller, and crusher parts.
SFH-MN-OSFH-MN-O--------For hardfacing of crusher cone and hammer or for buttering.
SFH-35-OSFH-35-O--------It is used for the repair of gear, mine car wheel and tractor roll.
SFH-41-OSFH-41-O--------It suits for metal to metal abrasion.
SFH-51-OSFH-51-O--------It provides excellent abrasion resistance and impact resistance.
SFH-56-OSFH-56-O--------Excellent abrasion resistance and moderate impact resistance .
SFH-61-OSFH-61-O--------High hardness and excellent abrasion resistance.
SFH-65-OSFH-65-O--------Excellent abrasion resistance at high temperature.
SFH-67-OSFH-67-O--------The deposit shows very high hardness and excellent abrasion resistance.
SFH-70-OSFH-70-O--------The deposit shows very high hardness and excellent abrasion resistance.